MacQueen

You've loaded an old revision of the document! If you save it, you will create a new version with this data.

====== Raspberry Pi ======

===== 2025 3 7 =====

* make vlc run as a service https://forums.raspberrypi.com/viewtopic.php?p=1197517&hilit=vlc+in+crontab+fails#p1197517

===== 2025 3 2 =====

* power glitch seems to have toasted the SD card.
  * would not come up even after resetting the card.
  * ran the 2024.10.31 below but password is wembley01.
  * device is Raspberry Pi 3.
  * installed 64 bit OS. 
  * had to recompile libshutup.c.
  * still could not connect in living room until reset basement cat5, so OS was probably OK.

===== 2024 10 31 =====

* may toasted the existing 32 gig sd card
  * installed os on Onn 128 gig card using imager_1.8.5.exe
  * Pi is __version 3__
  * python, mousepad, and realvnc already installed
  * ssh, ran raspi-config and select interfaces, then I3 for vnc which starts the server
  * installed Idle
  * added */2 * * * * python p8.py to crontab to check wcpe every two minutes
  * code is in synshare/software/rasp

===== 2022 02 7 =====

* used [[https://www.raspberrypi.com/software/|RP imager]] to install OS on [[https://www.amazon.com/dp/B08GY8NHF2|256 Samsung]]
  * wembley01
  * installed Samba
  * modified [[https://raspberrypihq.com/how-to-share-a-folder-with-a-windows-computer-from-a-raspberry-pi/|smb.conf]]
  * <code>workgroup = WORKGROUP
wins support = yes</code>
  * <code>[PiShare]
 comment=Raspberry Pi Share
 path=/home/pi/Videos
 browseable=Yes
 writeable=Yes
; chnage this after videos are copied
 only guest=no
 create mask=0777
 directory mask=0777
 public=Yes</code>
  * did a chmod Videos 777
  * vnc server was already installed. sudo apt-get install realvnc-vnc-server 
  * turn on ssh and vncserver in config using //sudo raspi-config// from terminal
  * made /home/pi/Videos a share
  * Can view videos remotely

===== 2022 01 27 =====

* installed Samba
  * modified smb.conf
  * made /home/pi/Videos a share
  * Can view videos remotely

===== 2020 05 13 =====
  * Pi 3 Model B+ with 1 gig memory
  * Assembled the case using this video: canakit.com/pi-case
  * Followed direction in manual to format the SD card and install NOOBS
  * Booted up and installed Raspian
  * did sudo apt-get xscreensaver
  * did sudo apt-get gtk+2.0 
  * followed directions at silicondust.com/support/linux to download and make hdhomerun software
  * ran hdhomerun_config_gui to scan channels. could view channel 4 HSN.
  * what program to use to view all channels and select them?

===== raspap =====

* __does not uninstall cleanly!__
  * installed using directions from website
  * shows up in wifi as raspi-webgui
  * lenovo can connect and browse web with admin/secret
  * lenovo has address 10.3.141.220
  * wlan address is 10.3.141.1 
  * hostapd.conf is in /etc/hostapd
  * uninstaller is in /var/www/html/installers
  * can still vnc to rasp eth0 of 10.0.0.63.
  * can run gui by pointing browser to 10.0.0.63/system_info
  * login with admin secret

* simpler solution would be to make bell modem give rasp a static eth0 address
  * connect rasp to the bell modem with a cable.
  * users look for wireless 'rasp' and connect to it
  * warn them that there is NO internet access!
  * then use file explorers to find rap]sp on the network.
  * then raspAp not needed on rasp

* good [[https://www.youtube.com/watch?v=GdNK2p3RhB0|raspap]] video here
  * [[https://www.youtube.com/watch?v=qMT-0mz1lkI|script]] from 2019 here
  * other videos use OpenWrt which is for embedded devices or have much conf editing so try simple solution above

Edit summary

Note: By editing this page you agree to license your content under the following license: CC Attribution-Share Alike 4.0 International